Re: Stepper motors


"Periproct" <Periproct@xxxxxxxxxxxxxx> wrote in message
news:Io-dnbJhf5wg17vanZ2dnUVZ8sSrnZ2d@xxxxxxxxx
I'm setting up a small CNC mill to educate myself before taking the plunge
on a larger machine and I have a few questions about the stepper motors
and
stepper driver boards.

Firstly, the motors have what looks like 7/0.2 wires attached and
according
to the people I bought the machine from they are rated at 2 amps. Surely
that is very fine wire for so high a current.


Not an unusual size. The stepper driver can still force 2 amps through it,
even with many ohms of internal/external wire resistance.


Secondly, the driver boards have an potentiometer to adjust the current.
My
simple mind says the motors will take the current they require or is this
some kind of current limiting.


It -would- take the current it needs, if only you supplied the motor with
it's normal working voltage, which may only be about 2Vdc.
I'll bet though that your controller is being fed from something like a
24-40Vdc supply.
The idea is for the drive PCB to force a fixed (usually marked on
nameplate), controlled current through the motor winding, that will not be
affected by connecting wire resistances, or the evil, increasing coil
impedance which is a big problem at faster and faster stepping rates.
One problem is, that as the driver PCB has so much voltage headroom to play
with, a careless setting of the current adjust pot will happily force say 2
Amps through a 1/4 amp motor. A minute later and the motor is toast.
The driver PCB doesn't mind what's on the end of it's wires.


Lastly, would it be sensible to adjust the boards to a slightly lower
current?
I've set all three boards to 2 amp and already killed one board.


Yes. Set the current lower. You can always wind it up later if more
performance is needed. I'd start at maybe 1/2 amp (or less) and see how it
goes.
At continuous full rated current, the motors bodies can run -very- hot. This
is most noticeable with the motors stopped or doing little work.
Because of this waste of power some drive boards allow entering a
low-current/sleep mode, if no steps have been sent for a couple of seconds.
This can be about 10%-50% of nominal current.


.

Relevant Pages

  • Re: downward noise reducing ant?
    ... elevator shack. ... You first need to differentiate between radiated noise and conducted ... The path for the motors' heavy current is through a wire. ...
    (rec.radio.amateur.antenna)
  • Re: Stepper motors
    ... on a larger machine and I have a few questions about the stepper motors ... even with many ohms of internal/external wire resistance. ... The driver PCB doesn't mind what's on the end of it's wires. ... I've set all three boards to 2 amp and already killed one board. ...
    (sci.electronics.basics)
  • Re: Best ignitor kit.
    ... The wire is to wide to fit ... most smaller motors (24 awg duplex instead of 26 awg duplex) and the ... double dipped fixed that) Sure, you can't use it on most 24mm motors, ... The new MF-12 measures 0.098 inches in width where as the ML-12 ...
    (rec.models.rockets)
  • Re: electric motor
    ... Easiest motors to deal with are the 'general purpose' fractional HP motors. ... These will come in 1750 or 3450 rpm, have a flat base to mount with, better ones are dual 120/240 volts and/or reversible. ... I am not an electrician and have no ... to use and easy to wire? ...
    (rec.crafts.metalworking)
  • Re: Questions about size of magnetic wire to use
    ... >> More phases won't make more energy. ... 20 gauge magnet wire is small. ... efficiency of the generator. ... AC induction motors can also be used to generate power - and they are ...
    (sci.electronics.misc)