Re: LED Reverse Polarity Protection


"Stephen J. Rush" <sjrush@xxxxxxxxxxx> wrote in message
news:LYydndhov9TcBDPanZ2dnUVZ_ofinZ2d@xxxxxxxxxxxxxx
On Sat, 09 Feb 2008 22:10:38 -0800, BobW wrote:

"Dave.H" <the1930s@xxxxxxxxxxxxxx> wrote in message
news:227bac2d-4517-4cd5-8880-d8eaca9b7c4a@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Hi, I'm considering using a high brightness LED in an old incandescent
flashlight, in series with a 220 ohm resistor, for use with a 6 volt
lantern battery, but I also want some type of reverse polarity
protection for the led, as I'm putting the LED, resistor, etc. in a
regular flashlight lamp base. I assume this would most likely be done
with a diode, perhaps a 1N400x type, but how would I wire this up?

You're on the right track. You don't need a high-current diode like a
1N400x, however. A 1N4148 or 1N914 will work fine because the maximum
current will always be very low (6V/220ohm = okay for a small signal
diode).

Anyway, just put the diode across the led backwards. That is, put the
anode
of the diode to the cathode of the led, and the cathode of the diode to
the
anode of the led. That way, if your flashlight batteries are installed
backwards, the diode will conduct the current (I=6V/200ohms) and the
reverse
voltage across the led will be limited to under 1V.

A high-brightness white LED might well draw more current than a
small-signal diode can handle, so a 1N4001 (50V, 1A) diode might be
better. Any of the 1N400x series will work; they're all cheap and easy to
find, but the 4001 is the cheapest. I'd put the diode in series with the
LED and adjust the value of the ballast resistor to allow for the 0.6 volt
forward drop of the diode. A better solution would be to look up one of
the switching regulators usually used with high-power LEDs.
With a simple resistive ballast and 6 volts, the resistor will dissipate
at least as much power as the LED.

There's a 220ohm resistor in series. It don't matter what type of led is
installed. The max reverse current is determined by the battery voltage, the
series resistor, and the voltage drop across the protection diode (note the
absence of the led's effect on this).

Bob


.

Relevant Pages

  • Re: 12V regulator
    ... or was my omission of the word diode prior ... a series diode will not protect aLED from reverse ... reverse drop from exceeding the LED's reverse voltage rating. ... blue one in the OP's switch, may be more sensitive, but I found blue LEDs ...
    (sci.electronics.design)
  • Re: LED Reverse Polarity Protection
    ... flashlight, in series with a 220 ohm resistor, for use with a 6 volt ... with a diode, perhaps a 1N400x type, but how would I wire this up? ... LED and adjust the value of the ballast resistor to allow for the 0.6 volt ... the switching regulators usually used with high-power LEDs. ...
    (sci.electronics.basics)
  • Re: Calculating LED resistors- long winded
    ... You will need to drop the resistor ... LEDs don't have persistence like a real bulb does. ... that's why I posted about peak voltage. ... 1N4937 type diode in series with the LED. ...
    (rec.games.pinball)
  • Re: LED Reverse Voltage
    ... I'll limit it through a 10K resistor also.... ... it is common for LEDs to be rated for max. 5 volts ... reverse voltage and have a high rate of doing nothing wrong with 12 volts ... having a reverse protection diode. ...
    (sci.electronics.basics)
  • Re: LED holiday lights
    ... And as I said, by using the diode, he ... was able to tell that the LEDs WERE NOT "all pointing the same way," to ... Half the string would light. ... Reverse biasing will not hurt a diode as long as the proper ...
    (alt.home.repair)