Re: Putting Red LED's In Osram Dot it light

On Feb 20, 11:18 pm, Tom2000 <ab...@xxxxxxxxxxxx> wrote:
On Wed, 20 Feb 2008 02:29:30 -0800 (PST), "Dave.H"

<the19...@xxxxxxxxxxxxxx> wrote:
I want to put 16,000 mcd red LEDs in an Osram Dot it light for working
outside when I don't want my night vision affected, the light in
question has 3 white LED's and a resistor (red-yellow-black-gold-
brown) voltage measured from the pins of the LED's is 3.122 VDC. How
would I go about installing these 2.0 volt red LED's? Do I just
change the resistor, if so what value? Unit is powered by 3 AAA
batteries.

Dave,

It sounds like the white LEDs are in parallel, drawing (theoretically)
about 20 mA per LED.

If you wanted to put your red LEDs in there at the same current draw
and wired in parallel, you'd use something like a 43 ohm 1/4 watt
resistor. If the LEDs are too bright, use a larger value resistor and
gain increased battery life. (56 ohms, approx. 15 mA. 82 ohms,
approx. 10 mA. 150 ohms, approx. 5 mA. 820 ohms, approx. 1 mA.)

If you find that one LED is much brighter than the other two with your
LEDs wired in parallel, use three individual resistors, one for each
LED, to balance the currents. 120 ohms per LED will give you approx.
20 mA per LED. Larger value resistors will lower the current.

Here's how to calculate the resistors and currents:

R = (Batt voltage - LED voltage) / current

Current = (Batt voltage - LED voltage) / R

You want to limit the current through each LED to a maximum of 20
milliamps. High-brightness LEDs put out a decent amount of light at 5
milliamps, or even 1 milliamp. For an outdoor night light, 1 milliamp
might be enough if all you want to do is look at a chart at close
range, or something like that. Experiment to find the current level
that meets your needs. (You might even find that a single LED
provides adequate brightness.)

If you have room in that housing to add a miniature switch, you could
connect two of the LEDs, biased for fairly high current, switched from
the existing power switch. Use your extra switch for a single
LED/resistor combo, biased for very low current. That would give you
a choice between dim and bright light levels, depending upon your
needs.

Have fun!

Tom

I think I have a 47 ohm resistor stashed somewhere, I'll dig that out
and try it once I get the LED's tomorrow.
.

Relevant Pages

  • Re: About some parts on logical circuits
    ... chance on some pushbutton switch logic? ... I wasn't aware of the pull-down resistor issue. ... Since each transistor will have to feed a dozen of LEDs at 40mA ... Run the LEDs off the transistor's collector. ...
    (alt.guitar.amps)
  • Re: how to control LED array? (follow-up)
    ... > except I've modified some resistor values as I have now chosen LEDs: ... The columns are active high, and the rows are active low. ... You can use 470 ohms for them. ...
    (sci.electronics.basics)
  • Re: Putting Red LEDs In Osram Dot it light
    ... brown) voltage measured from the pins of the LED's is 3.122 VDC. ... Where R is the value of the resistor, in ohms, ... For example, If your LEDs are rated for a Vfof 2V at 20mA, ...
    (sci.electronics.basics)
  • Re: Cant get enough current for 1W Luexon LED even without resistor
    ... resistor but still only about 100ma current. ... want to be thinking in terms of voltage. ... life from any high power LED, is to pulse drive it. ... The level of these that some high power LEDs can ...
    (sci.electronics.repair)
  • Re: Cant get enough current for 1W Luexon LED even without resistor
    ... Then I tried without the resistor but ... the LED I have to raise the voltage to about 11V and of course I ... LEDs for a long time, and never suffered a problem with a switch-on ... max forward current quoted in specs, is for a short duration pulse. ...
    (sci.electronics.repair)
Loading