Re: Simple design - will it work


"Jim" <jim@xxxxxxx> schreef in bericht
news:4a548a82$0$25006$ed362ca5@xxxxxxxxxxxxxxxxxxxxxxxxx
Guys

I need to wire up a remote switch for a milling machine in my garage.

Rather than go into a lot of detail all I need to achieve is continuity
betwenn A & B on the linked diagram but I can only use a momentary switch
(SW1)

http://rapidshare.com/files/253373634/2443_001.pdf

Can someone confirm if the planned circuit will work ie when SW1 is
momentarilly closed then continuity will provided aacross A&B until the
12V
power is switched off.


Also on a different topic, I need to connect a 10k pot to my inverter to
vary the power output. Circuit diagram shows 3 connections,

1) +10V (Power terminal of Pot)
2) Analog frequency signal input terminal
3) 0VAnalog common point

Any idea how I identify which pin is which on my pot

Cheers

Jim




This circuit will not do what you want it to do. AB will be connected as
long as you keep the momentary switch pushed but will disconnect when you
release that switch almost immediately. To achieve your goal you need a DPST
relay as shown below. (View with fixed font.)


--+--------------------12V
|
|
| +-----+
| | | +---- A
| | | |
| | \ o \ o
X_|_ | \ x1 \ x2
|_/_|- | \. \.
| | o o
| | | |
+-----+ | +---- B
| |
| |
| o |
|=|> |
| o |
| |
| |
| |
-+-----------+----------- -
created by Andy´s ASCII-Circuit v1.24.140803 Beta www.tech-chat.de

If you have the two SPDT relay as in your drawing already available, you can
use them by switching the coils in parallel.


--+------+--------------------12V
| |
| |
| | +-----+
| | | | +---- A
| | | | | | |
| | | o\ o o\ o
X_|_ Y_|_ | \ x \ y
|_/_|- |_/_|- | \. \.
| | | o o
| | | | |
+------+-----+ | +---- B
| |
| |
| o |
|=|> |
| o |
| |
| |
-+------------------+-------------
created by Andy´s ASCII-Circuit v1.24.140803 Beta www.tech-chat.de

As for your pot, you'd connect the pin in the middle to connection 2. The 1
and 3 connection come on both outside pins. You can exchange when required.

petrus bitbyter





.

Relevant Pages

  • Re: Onan Generator will not start
    ... I checked the coil voltage, ... poor connection from the control board to ... The lead that runs to the coil is pin 12 of P1, ... start/stop rocker switch is sticking in the start position. ...
    (rec.outdoors.rv-travel)
  • Re: Servo Reverser
    ... elcetronics so the switch basically changed the polarity of the pot. ... wiper connection was left as is. ... The inline servo reverser I had originally would regularly ...
    (rec.models.rc.air)
  • Re: Help with long term network problem
    ... Using a CNET network switch connected to a CNet Wireless G router Model ... Having the chart listing all of the computers is a great start. ... /all" shows only an Intel 2200BG WiFi connection - no Ethernet is apparent. ...
    (microsoft.public.windowsxp.network_web)
  • Re: Mystifying switch problem
    ... Losing the connection in the context of my post meant that the ... I bought a THIRD switch, this one a SOHO variety by D-Link, and ... IPs to all the devices on the network, ... more precise Network variables that stop function, on all computers. ...
    (microsoft.public.windowsxp.network_web)
  • Re: Problems with a switch
    ... I work in a group with four people and we have one internet connection. ... So we bought a switch - however we have trouble ... of the computers 'look like' one computer to the ISP modem. ...
    (alt.comp.hardware.pc-homebuilt)
Loading