Re: Making lightning with a thin wire


Electroniker wrote:
Winfield Hill wrote:
Ignoramus17570 wrote...

Another question, can such things be viewed with an autodarkening
welding helmet. (1/20,000th of a second darkening time)

Be careful: 50us isn't fast enough.


--
Thanks,
- Win

While in college, I worked in an on campus instrumentation lab. Our
job was to build whatever it was that researchers needed. I was given
the task of designing an safe fuse and detonator for an
acetelyne/oxygen bomb developed by the US Bureau of Mines. It was
called a CERB (Controlled Electronic Rock Blaster).

The fuse consisted of a piece of #30 wirewrap wire strung between two
mounts. This was sealed into the gas mixture housing. The fuse was
considered safe since only a huge amount of energy could cause
ignition.

Ignition was accomplished by charging a large capacitor (5 uF) to 15
KV. This cap was the input to a triggered spark gap. The output was
the #30 wire in the gas mixture chamber. The cap was charged, arming
the circuit, and then the spark gap trigger by a thyraton, causing the
cap to be discharged into essentially a short.

The discharge event lasted less than 5 usec, in which time, the wire
would vaporize igniting the gas mixture. A combustion wave would
propagate down the cylinder, and at 100K psi, a shear plate would
release, sending a shock wave down toward the area to be "blasted".
The theory was that the shock wave could be more controlled, better
directed, and the blast would consume less energy than conventional
explosives.

This was one of the best projects I ever got to work on. The first
test was in a basement lab and we had no idea what the effect of that
kind of force would be. The room was destroyed. The shear plate
punched a hole in the concrete wall, all the lights were in shambles.
Later, a steel plate was used as the target and even this ultimately
had a hole abraded through it.

The first field test was also spectacular. The CERB was untethered,
and when detonated, shot straight up in the air like the rocket it was
with only the fuse and detonator wires to limit its flight.

Other labs were working on the approach as well. The highest energy
data point could never be replicated because the researcher lost his
lab in the experiment...


Don't you just hate it when that happens!

What explosives did you use? Perchlorate and...???

Michael

.

Relevant Pages

  • Re: Making lightning with a thin wire
    ... (1/20,000th of a second darkening time) ... I worked in an on campus instrumentation lab. ... The fuse consisted of a piece of #30 wirewrap wire strung between two ...
    (sci.electronics.design)
  • Re: Battery drain update (Dodge Xplorer)
    ... light a "fridge failure" light if the switch cooled off. ... Fit it in place of the fuse. ... 500 ma would also be in the ballpark for a 12 volt relay or contactor coil. ... Tugging the wire leaving the fuse will ...
    (rec.outdoors.rv-travel)
  • Attn: Jumpster Jiver - Ohmite VT4-F
    ... It appears the fuse socket ... The fuse has continuity. ... to 140 and back while feeling the dial and looking at the brush. ... and gently wipe the lapped wire mating surface. ...
    (sci.electronics.repair)
  • Re: Attn: Jumpster Jiver - Ohmite VT4-F
    ... It appears the fuse socket is broken and had no continuity between the front of the fuse under the cap and the terminal. ... look at the lapped surface of the windings (where it meets the brush) and look for burn marks or discontinuities. ... and gently wipe the lapped wire mating surface. ...
    (sci.electronics.repair)
  • Attn: Chris - Ohmite VT4-F Variable Transformer
    ... It appears the fuse socket ... The fuse has continuity. ... to 140 and back while feeling the dial and looking at the brush. ... and gently wipe the lapped wire mating surface. ...
    (sci.electronics.repair)