Re: Linux and spice


"Jamie" <jamie_ka1lpa_not_valid_after_ka1lpa_@xxxxxxxxxxx> schrieb im
Newsbeitrag news:Ve7Sh.15$rV.4@xxxxxxxxxxxxxxx
Ian Bell wrote:

Ian Bell wrote:


Rich Grise wrote:


On Fri, 06 Apr 2007 20:08:12 +0100, Ian Bell wrote:

Rich Grise wrote:


I downloaded the latest and greatest source, so I have:

$ wine --version
wine: glibc >= 2.3 without NPTL or TLS is not a supported combination.
It will most likely crash. Please upgrade to a glibc with NPTL
support.
wine-0.9.34
$

Hmm - this is the first time I've tried wine --version; I don't
understand that glibc thing: I'm running Slackware 11.0;

No need to compile it. Go to www.linuxpackages.net where you will find
a
Slack pack for wine for slackware. This link should get you straight
there.

http://www.linuxpackages.net/search_view.php?by=name&name=wine&ver=11.0

OK, so I've done that, and I get:
###
$ wine /G/Software/swcadiii.exe
wine: glibc >= 2.3 without NPTL or TLS is not a supported combination.
It will most likely crash. Please upgrade to a glibc with NPTL
support.
wine: Unhandled page fault on write access to 0x003ffd80 at address
0x60cf1103 (thread 0009), starting debugger... wine: glibc >= 2.3
without
NPTL or TLS is not a supported combination.
It will most likely crash. Please upgrade to a glibc with NPTL
support.
wine: Unhandled page fault on write access to 0x003ffd80 at address
0x60936103 (thread 000b), starting debugger... wine: glibc >= 2.3
without
NPTL or TLS is not a supported combination.
It will most likely crash. Please upgrade to a glibc with NPTL
support.
err:seh:raise_exception Unhandled exception code c0000005 flags 0 addr
0x6000c04b

$ wine: Unhandled page fault on write access to 0x003ffd80 at address
0x60936103 (thread 000d), starting debugger... err:seh:raise_exception
Unhandled exception code c0000005 flags 0 addr 0x6000c04b
err:seh:raise_exception Unhandled exception code c0000005 flags 0 addr
0x6000c04b

$ wine --version
wine: glibc >= 2.3 without NPTL or TLS is not a supported combination.
It will most likely crash. Please upgrade to a glibc with NPTL
support.
wine-0.9.33
###

So do I need a different library or something?

Thanks,
Rich

Very interesting. I installed switcherCAD using an earlier version of
wine
and have only just upgraded to the version I told you about. I don't
normally run it from the command line but I just tried it and I get the
same initial glibc message you did but then it runs OK. Clearly the
installer will not run at all now from your own tests. I need to look
into
this further.

Ian


Right, checking on linuxpackages.net reveals that this version of wine is
meant for 2.6 kernels and the error occurs if you run with a 2.4 kernel.
So
you could upgrade to a 2.6 kernel or roll back wine far enough to be 2.4
kernel compatible. I run 2.4 kernel so I have to make this decision
too.Not
sure which way to go yet.

Ian
isn't always best to work with the newest ?

Hello,

There is no reason not to upgrade to a Linux with version 2.6 kernel.
I tried LTspice and Wine with the latest Ubuntu, Suse and Mandrake
and it worked, even with the latest Wine version. OK, it was a few
months ago, but I assume it's still true.

Best regards,
Helmut


.