Simple mosfet question

I have a simple circuit where I want to convert a digital input from
0-5V to an inverted signal from 0-12V. ie, 0V into the circuit = 12V
out, and 5V into the circuit = 0V out.

I don't have the means to get a schematic up, but I've tried to draw
it with text below (but it probably won't show up right), so I will
describe the simple circuit and I think it will be clear:

There is a 2N7000 N-ch mosfet transistor, with the source tied to
ground. The gate is tied directly to the input. The drain is tied to
a resistor, 10k, and the other side of the 10k resistor is tied to a
battery, +12V. The output is connected to the drain, and is used to
feed the clock inputs of 2 CMOS ICs. There is a 470pF filtering
capacitor tied from the output to ground.

My question is, can anyone see how this circuit would blow the
transistor? Is this an OK way to hook it up? Should I maybe add
another 10k resistor between drain and output (before the cap) to
better protect the transistor? I realize that doing this would bring
the output voltage down very slighlty, but that's fine if it is needed
to protect the transistor.

I'm asking because I've hooked up the circuit more than a few times,
and it always works at first / for a while, but sometimes the
transistor blows unexpectedly and I don't know why yet. I think it is
because I was damaging the transistor during install (with ESD, I was
not using protection at the time, but I learned my lesson!), but I
want to make sure it isn't actually a circuit problem too.

Sorry that I can't get a schematic up, I don't have a place to upload
files while I'm at work. I hope I have made it clear enough :)


+12V
|
|
/
\ 10k
/
|_______OUTPUT
__|
| |
INPUT _____| |__
|
|
|
GND

.

Relevant Pages

  • Re: astable multivibrator issues - 2N3904s work, but not TIP31As
    ... the circuit would not oscillate unless I briefly disconnected then re- ... The main issue folks have is that they forget to bypass the power supply, ... As a side note, the easy way to build a square wave oscillator from a cmos 555 is to connect the output pin to a resistor, then connect the other side of the resistor to ground through a capacitor. ... For your application, you might use the discharge to directly drive one LED, and have the other LED driven by a power PMOS or PNP transistor. ...
    (sci.electronics.basics)
  • Re: Simple mosfet question
    ... describe the simple circuit and I think it will be clear: ... There is a 2N7000 N-ch mosfet transistor, ... a resistor, 10k, and the other side of the 10k resistor is tied to a ... Need to learn how to apply control theory in your embedded system? ...
    (sci.electronics.design)
  • Re: Help! Capacitive coupled transistor setup
    ... It is the reference circuit from Kodak for their CCD imaging sensors. ... with the emitter of each transistor and its corresponding ... resistor to the base of one of the transistors. ... end of the resistor to V high and observe the LEDS, ...
    (sci.electronics.design)
  • Re: Newbee: Optocoupler to BasicStamp
    ... > the circuit to work. ... > pulled up by a 10K resistor. ... > I cant get the Stamp to detect on/off states. ... The input to the base of a transistor is what normally turns it on. ...
    (sci.electronics.basics)
  • Re: discrete comparator
    ... >> in a circuit to limit the output of an antique generator. ... >> the value of the 470K hysteresis resistor is just a guess. ... >> from the collector to base of the PNP transistor. ... >> so it serves both current limiting and voltage regulation. ...
    (sci.electronics.design)