Re: Problem with PIC & LCD display

On Thu, 1 May 2008 17:51:39 +0100, Steve H <steveu@xxxxxxxxxxxxxxxx>
wrote:


I'm having a problem with a fairly simple project incorporating a
16F877A PIC and a 4x20 alphanumeric display module. The circuit
interfaces with other logic ICs, though these can be removed from the
circuit to isolate the problem.

The circuit is fed, under test conditions, from a linear 12v power
supply. The 5v regulator on the circuit board is decoupled using 100nf
ceramic capacitors. There is similar decoupling on the PIC itself, and
at other places e.g. decoupling the 5v supply on the connector to the
LCD display. I have also fitted a 100uH coil in the supply to the 5v
regulator to reduce any effects from spurious noise on the supply line.

The problem I'm having difficulty solving is that the display will
intermittently go blank. It will go blank, seemingly when the display is
written to by the PIC, either (a) due to a spike/noise on the mains
supply (this can be intermittently reproduced by repeatedly turning on
and off a piece of mains powered equipment on the same circuit), or (b)
when the 0v rail (not even necessarily close to the LCD display) is
touched by for example a multimeter probe. This is the most consistent
way of producing the fault. The multimeter can be turned off and the
other probe not connected to anything for this to happen. The PIC
doesn't appear to be affected by any of this as it can be shown to still
be operating as expected.

Are you sure it's not resetting?

I've experienced similar issues before in my limited experience of
building small projects with PICs. I had issues with a 16F84A resetting
itself when the 0v rail close to the IC was touched with a screwdriver.

Can anybody suggest what vital consideration for circuit design I'm
missing. I'm at a bit of a loss as to what I'm doing wrong.

Thanks.

What else EXACTLY is this PIC circuit connected to (off board in
particular)? How long is the cable to the LCD display? What kind of
equipment is this? Can you link to a photo? Is it a proper PCB or a
plugboard?
Best regards,
Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
speff@xxxxxxxxxxxx Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
.

Relevant Pages

  • Re: Problem with PIC & LCD display
    ... 16F877A PIC and a 4x20 alphanumeric display module. ... circuit to isolate the problem. ... at other places e.g. decoupling the 5v supply on the connector to the ... when the 0v rail (not even necessarily close to the LCD display) is ...
    (sci.electronics.design)
  • Req: Schematic for BASIC electromyogram (EMG) - biofeedback type device
    ... I've used a commercial unit in the Occupational Therapy clinic, but it has a fancy LCD display with mmv readings, timers, etc. ... I visualize an output of a simple string of LEDs. ... circuit boards to be comfortable with the process. ... Subject: Req: Schematic for BASIC electromyogram (EMG) - biofeedback type device ...
    (sci.electronics.design)
  • Re: Problem with PIC & LCD display
    ... 16F877A PIC and a 4x20 alphanumeric display module. ... circuit to isolate the problem. ... when the 0v rail (not even necessarily close to the LCD display) is ... I'd also not trust that reset pin. ...
    (sci.electronics.design)
  • Re: Problem with PIC & LCD display
    ... I'm having a problem with a fairly simple project incorporating a ... 16F877A PIC and a 4x20 alphanumeric display module. ... circuit to isolate the problem. ... when the 0v rail (not even necessarily close to the LCD display) is ...
    (sci.electronics.design)
  • Problem with PIC & LCD display
    ... I'm having a problem with a fairly simple project incorporating a 16F877A PIC and a 4x20 alphanumeric display module. ... The circuit interfaces with other logic ICs, though these can be removed from the circuit to isolate the problem. ... There is similar decoupling on the PIC itself, and at other places e.g. decoupling the 5v supply on the connector to the LCD display. ...
    (sci.electronics.design)
Loading