Re: Battery charger - cordless drill Ryobi




----- Original Message -----
From: "webpa" <webpa@xxxxxxx>

> Why do you think the charger is "overheating"? In a practical sense,
> if the charger isn't melting or smoking, then it is probably working as
> designed.

With the older batteries, the temp of the charger is at a level that I can
touch and hold my hand on it during the charge cycle of several hours.

Same charger and new batteries - after 20 min I cannot hold my hand on it.
I disconnect it and let it cool. Then plug in again.

> Why do you think the new batteries are of the same "...design"? If they
> were, then they wouldn't draw any more current from the charger (thus
> making it run hotter) than the old batteries. Seems possible the new
> battereis are, in fact, not of the same internal design.

Perhaps this is the question - if they are. Both have the same voltage, mAh
rating. If Ryobi tech support was better, they would explain the diff.
There cleary is some diff, as evidenced by the heating of the charger.

> he cells may use a slightly (or entirely) different chemistry and/or
physical
> construction, even though they have the same voltage and current
> ratings.

This is why I'm asking the question. Did not think that slight difference
in chem or construction would make that much diff. NiCad batteries have
been made for ages and used the same chargers.

> Another fact is that no two manufacturing
> facilities make "NiCad" or "Ni-Mh" or "Lithium" cells exactly the same
> way...even when building to the same specs.

Only one of these 4 batteries clealry says NiCad on it. All others are
missing that info, although they are meant for the same drill.

> Finally: If the new batteries require an "adaptor cord" to attach them to
the old charger,
> that is a pretty substantial hint that SOMETHING is rather different.

The adapter is a short piece of wire that changes the plug - no electronics
involved. It is sold with these new batteries to all usage with existing
chargers.

The mystery is that these apparently "very similar" batteries have such a
different characteristics, when it comes to charging.

> Bottom line: If the new batteries charge and then power the drill, use
> them until they fail to do so.

In a way they do, but I have been babysitting the charging process, being
afraid to just leave it on for a long time - fearing a meltdown of the
charger.

Would be much nicer if Ryobi provied good info on their products, so I would
not have to bother folks here :-) Of course you do not find out these
things until after you buy it and a bit later try and observe.

Rich


.



Relevant Pages

  • Re: More Battery Recharging Questions
    ... I have a new Yamaha EF1000isc generator, ... I suspect that the charger may be a lot faster. ... I believe that charger is "only" a 10 amp charger. ... If you have golf cart batteries and run them half ...
    (rec.outdoors.rv-travel)
  • Re: nb Virgo
    ... Surely this is only the case if there's a heavy drain on the batteries when the engine isn't running and when there's no shoreline mains supply. ... I can't imagine a situation where the domestic batteries are very discharged and there's mains to drive the charger. ... The other point is that the modified sinewave inverters have had to be *severely* built down to a price in order to keep some market share. ...
    (uk.rec.waterways)
  • Re: Replace mower or just mower battery?
    ... >> Batteries Plus is right in town, Houston, TX. ... >> charger into the mower and plugged in charger ... But I remember if the mower end is unplugged, ... When I unplug the charger from the trimmer, ...
    (rec.gardens)
  • Re: Problem with Acid-Free Batteries
    ... you think that I should get a charger with more "juice" to it. ... about these batteries. ... When I first bought the scooter (I was going to go through Medicare, ...
    (sci.electronics.basics)
  • Re: Time change..smoke
    ... The new technology in batteries is SANYO Eneloop (couple others ... as time increases less discharge ... Last is a charger unit, optionally, which can become an intricate ...
    (alt.coffee)