Re: Need help with older RCA Tv with solder ground problem

You don't need a schematic, it cannot be any simpler..
Plus a schematic isn't going to help you.

"stryped" <stryped@xxxxxxxxxxx> wrote in message
news:1141151359.978273.327220@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
x-no-archive:yes

Is there anywhere on line where I could find a schmatic for this tv to
help with the repair?
kip wrote:
Yes remove the Tuner from the board.

kip

"stryped" <stryped@xxxxxxxxxxx> wrote in message
news:1141143808.847571.119510@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
x-no-archive:yes

I am sorry. I know you have to de solder the tuner cover. I meant the
board the tuner is mounted to in order to be able to solder the tuner
effecticely if that makes sense.
kip wrote:
Well of course you have to unsolder it to remove it...and when you've
repaired it solder it back .
What the think its just sitting there ?

Slacken off chassis pull out and turn over use solder braid or sucker
to
remove solder.

kip

"stryped" <stryped@xxxxxxxxxxx> wrote in message
news:1141139213.719136.241570@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
x-no-archive:yes

What is involved taking this out? Do I need to desolder anything? DO
I
need to flip the tv over to get to this? Again, many thanks!
kip wrote:
Ok Remove the back of the TV .
You will see what is on the other end of the fitting that you are
wiggling.
That's the tuner ,remove it then take of the cover and get out the
mag
glass and reflow the bad connections.
Done many of those.

kip

"stryped" <stryped@xxxxxxxxxxx> wrote in message
news:1141134611.776119.86280@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
x-no-archive:yes

I have a :

Model # G35830WK


Chasis # CTC169JS6

With stations that go in and out. Wiggeling the coax sometimes
fixes
it. I am assumming this is the notorious tuner ground problem. I
have
not opened up the tv yet. Does anyone have a diagram on where the
tuner
is and what needs to be taken off to get to it to re solder the
tuner
shield?

I have also read elsewhere that some have fixed this by soldering
a
jumper wire from the shield to a ground. Is this an acceptable
fix
for
those whose soldering skills may not be stellar? What ground
would
you
run the jumper wire to?

Thanks for your help!






.

Relevant Pages

  • Re: Need help with older RCA Tv with solder ground problem
    ... help with the repair? ... kip wrote: ... I know you have to de solder the tuner cover. ...
    (sci.electronics.repair)
  • Re: Need help with older RCA Tv with solder ground problem
    ... Will this be acceptable for this repair? ... kip wrote: ... I know you have to de solder the tuner cover. ...
    (sci.electronics.repair)
  • Re: Need help with older RCA Tv with solder ground problem
    ... type" and nneded the pencil type. ... kip wrote: ... I know you have to de solder the tuner cover. ...
    (sci.electronics.repair)
  • Re: RCA problem fixed sort of
    ... If however the tuner ... is vertically mounted, with solder connections going thru the board, then it ... I posted last week about CTC chasis channels going in and out. ... the element of the new coax until it melted the old solder. ...
    (sci.electronics.repair)
  • Bad tuner follow up
    ... Subject: Re: Bad tuner? ... of the legs, so the only way I know to change it is to have small ... each out until they are all removed, the carefully solder wick the ... Better than replacing tuner for $92.00. ...
    (sci.electronics.repair)