Re: Generac 7500

ellombris@xxxxxxxxx wrote:
Fred McKenzie wrote:
In article <1164938070.570177.252870@xxxxxxxxxxxxxxxxxxxxxxxxxxxx>,
ellombris@xxxxxxxxx wrote:

I bought this generator a few weeks ago, used. It worked fine, but
stopped putting out any power. I contacted repair people, the local
repair facility only works on bigger units, but the man said it was
most likely the voltage regulator. Got the regulator on line and
installed it, I get power now. The 120v recepticles put out 50 v. and
the 220 put out approx. 120v. Any ideas, suggestions, referals? Thanks.
Ellombris-


I have downloaded some Generac manuals from
http://www.generac-portables.com including a couple 5500 watt units
(1314-0 and 9885-3). Both of these use the 83970, called a "System
Control Board".

The 83970 has a trim pot that sets voltage. Some models have the board
mounted with the trim pot next to a rubber plug on the left side of the
connector panel. If your model has this board, it might easily be
misadjusted. Try adjusting it for an initial value of 124 Volts output
with no load. A small adjustment can make a large difference in output!

There is also an 84132, called a "Power Regulator Board" on the diagram
and "Assembly, Drive Module, Power Regulator" on the parts list. This
module controls current to the rotating field. It has no adjustment
itself, but is driven by the System Control Board. Was that the module
you replaced?

If you study the problem further and still can't solve it, check out the
"Generators and Motors" forum at
http://www.smokstak.com.

Fred

The unit I have is a 7500 not the 5500, and I do have a parts list and
schematic for this generator. Thank you for your advice. I spoke to a
tech for the local company that works on larger units and he told me,
the 84132 has an adjustment screw on it. That is what I'll be trying
next. My kid works nights so I won't be running the generator 'till
Sunday, his day off.
Thank you you for your help, if this works I'll post that The problem
is solved, if not I'll be begging for help again and will check out the
websute you suggested.

Hi...

Just playing the devil's advocate for a moment...

Difficult to tell where any of us are in the world, so can't
even guess at where you might be, but those just about 1/2 voltages
might not be a coincidence...

It's not possible that you're in the UK and bought a North American
regulator, is it? :)

Take care.

Ken
.

Relevant Pages

  • Re: "Secret" Overvoltage Protection?
    ... I'm glad that the protection circuits appear to have worked without ... wiring to bypass the regulator (Generator armature to +12V, ... when the power came up, ...
    (rec.aviation.homebuilt)
  • Re: Generac 7500
    ... stopped putting out any power. ... most likely the voltage regulator. ... The 83970 has a trim pot that sets voltage. ... A small adjustment can make a large difference in output! ...
    (sci.electronics.repair)
  • "Secret" Overvoltage Protection?
    ... I wasn't sure if it was the generator or regulator, so I decided to do a bit of temporary wiring to bypass the regulator. ... So I left the power switches for both off. ... It read 8V at idle, but when the power came up, the voltage started to rise. ...
    (rec.aviation.homebuilt)
  • Re: Generac 7500
    ... stopped putting out any power. ... A small adjustment can make a large difference in output! ... called a "Power Regulator Board" on the diagram ... My kid works nights so I won't be running the generator 'till ...
    (sci.electronics.repair)
  • Re: Coaxial generator development
    ... Saving the generator from producing heat in both the rotor/stator and ... I'm afraid that only addresses the power OUTPUT, ... Yes, it does keep producing a voltage, and possibly an extremely high one at that; but heat comes from work, and a voltage is only half of that equation. ... The magnets will push the electrons as hard as they can be pushed, but the switching regulator has opened the circuit. ...
    (rec.aviation.homebuilt)
Quantcast