Re: CD-player erratic with CD-Rs


"EpsilonRho" <EpsilonRho@xxxxxxxxxx> wrote in message
news:wdh6j.4975$fl7.3119@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
This unit, TEAC PD-D850, is having difficulties playing audio CD-Rs. Not
every CD-R has
problems, only some of them and the problem consists in not locking into
the
tracks. The strange thing is that the CD-Rs are all of the same brand,
same
manufacturing date and even from the same canister!(TDK 48X, 80min). I
opened the unit thinking that perhaps the signal gain need to be slightly
adjusted. I found 4 potentiometers called:
1. T-OFFSET
2. T-GAIN
3. E F/BAL
4. FREERUN
I tried to adjust them with no avail. Any leads? What is the difference in
the signal between a normal CD and a CD-R?
Thank you very much,
Gene

The difference between a burnt CD, and a pressed one, is the reflectivity.
Some players, particularly those not specifically specced to play recordable
discs, have always struggled with them, and the problem becomes more
pronounced, as the laser wears.

Unless you really know what you are doing, you must not indulge in pot
twiddling. Some adjustments, particularly E-F balance and VCO ( your
"Freerun"??) are especially critical, and if you get both of them adjusted
even slightly wrongly, your problems will be compounded, and may start
extending into playability issues with pressed discs, as well.

Many Teacs use very 'bog standard' general quality Sony lasers from the
"KSS" series, and these have never been particularly renowned for their
ability to cope with home burns. If turning up the tracking gain ("T-GAIN")
pot did not at least make the problem better, and the lens is clean, then
you probably need to consider replacing the laser. Do not be tempted to up
the laser output power, by twiddling the pot on the laser's connector board.
If the laser is at all marginal, then doing this will speed its demise like
you wouldn't believe.

Meat's suggestion of reducing the burn speed is also a good one. You might
also like to try a disc burnt on a different drive, or using different
software, and you might also like to try a different manufacturer's disc.
Some lasers prefer the purple dye and some the green or goldy coloured
discs. A 'good name' disc is not always the best for all players. I have had
great success with one of the major UK supermarket's cheap and cheerful 'own
brands', for instance.

Arfa


.

Relevant Pages

  • Re: Current Advisability of going beyond 74 min on CD
    ... | But for a CD-R... ... the groove pitch is tighter ... the error rate will be lower with the more relaxed pitch. ... I distribute several thousand CD-R discs each year to corporate clients. ...
    (rec.audio.pro)
  • Re: archiving of digital photos
    ... nice thing about finer and finer data, the laser can always read the coarser data... ... discs the color of the light is important and a new device may not be ... CDs because the red DVD laser didn't work with all the IR dyes used in ...
    (rec.photo.digital)
  • Re: "Disc Cannot Be Played... Please Check The Disc"?
    ... Tried two discs. ... Put both discs in another player, ... Pulled the cover off, blew some air on the little laser thingie, then ... pretty sure that the laser is bad on its DVD side of things. ...
    (sci.electronics.repair)
  • CD-R Not Recognized byiMac
    ... I have a problem with CD-R discs. ... My iMac 333mhz tray loading CD drive also running Panther 10.3.2 will not ... The CD-r is readily recognized by the internal CD drive of the G4. ... The iMac CD drive does recognize commercially prepared CDs. ...
    (comp.sys.mac.apps)
  • Playstation 2 repair
    ... DVD discs. ... I've tried adjusting the laser height/angle and ... I've also adjusted the pots on the laser eye itself. ...
    (sci.electronics.repair)