Re: is there a way to increase the light of an LED with a dial?

I forgot to add - with the 12v, the LED went all the way to it
brightest and dimmest while turning the resistor. It was perfect, but
with the 5V, it peaked near the top of the resistors turn, and then
started to burn out. Not sure why with 5V it would burn out, but with
12V it did not.

On Jan 25, 7:29 pm, "Dave Plowman (News)" <d...@xxxxxxxxxxxxxxx>
wrote:
In article
<40d0ab8c-4a0d-4d17-96f4-826ac9203...@xxxxxxxxxxxxxxxxxxxxxxxxxxx>,
Victory <bionicbud...@xxxxxxxxx> wrote:

Ok, I tried something with a 10K variable resistor today at a school
today (they were kind to indulge me).
When I hooked up the 2 3V batteries in series to the resistor, it
dimmed immediately when I turned it only slightly. The falloff of
power to the LED went to the dimmest setting right away. On a whim,
we hooked it up to 12V and the dimmer worked all the way through the
entire turn. It was great. I am a little confused why this
happened? The LED comes with 2 3V batteries in series from the $
store and is quite bright. When hooked up to the 10K resistor, it
isn't as bright. So, the next basic question is - what happened?
Should i get a resistor that is less than 10K?

LEDs are current driven. Which in practice means a different value
resistor according to the supply voltage as you need to keep the current
through the LED constant for the same light output.

You can work out this series resistor value easily. The formula is:-

Vs - Vf
R = ------------
I

Where Vs is the supply voltage, Vf the forward voltage drop of the LED and
I the current in amps. You'd need to know the spec of the actual LED to be
accurate but making Vs 3V and I 0.020A will do for most white LEDs.

Which gives 150 ohms for 6 volts and 450 ohms for 12

The pot needs to go in series with a fixed resistor of the above value to
set the maximum current - otherwise you could burn out the LED. The pot
should be about 4 x the fixed resistor value to get a reasonably smooth
dimming range.

--
*Funny, I don't remember being absent minded.

Dave Plowman d...@xxxxxxxxxxxxxxx London SW
To e-mail, change noise into sound.

.

Relevant Pages

  • Re: Cant get enough current for 1W Luexon LED even without resistor
    ... resistor but still only about 100ma current. ... want to be thinking in terms of voltage. ... life from any high power LED, is to pulse drive it. ... The level of these that some high power LEDs can ...
    (sci.electronics.repair)
  • Re: Cant get enough current for 1W Luexon LED even without resistor
    ... Then I tried without the resistor but ... the LED I have to raise the voltage to about 11V and of course I ... LEDs for a long time, and never suffered a problem with a switch-on ... max forward current quoted in specs, is for a short duration pulse. ...
    (sci.electronics.repair)
  • Resistors for LEDs: the real answer
    ... First of all, while non-electronics types refer to the resistor in this use as a "dropping resistor", that's not really technically accurate: whats actually going on is that you're making a voltage divider network with a resistor in series with the LED. ... By putting a resistor in series with the LED, you're dividing the 24 volts between the resistor and the LED, because the whole idea is to make sure that the LED doesn't get too many volts and blow. ... Turning to my handy-dandy Jameco catalog, it appears that most garden-variety LEDs are rated at about 2 volts, some more, some less: close enough to be no never mind. ...
    (rec.models.railroad)
  • Re: Resistors for LEDs: the real answer
    ... while non-electronics types refer to the resistor in this ... whats actually going on is that you're making a voltage divider network ... Obviously, if you just put the poor LED across the 24 volts, ... the great majority of LEDs are rated at 20 mA; ...
    (rec.models.railroad)
  • Re: A useful website for LED array design
    ... with a 1 ohm resistor there won't be any current flowing. ... power supply voltage and perfect 3 x 3.5 fV LEDs like in this case: ... Offer the user a field to enter minimum percentage of the supply voltage to drop across any series resistor. ... Also it would be to force the number of LEDs in each chain to be as near the same as possible instead of putting a single left over LED in the last chain. ...
    (sci.electronics.basics)